Tips & problem solutions

Here we try to help. Should there be any problems.

    2. Wandstärke von innen dicker machen. 25

      • cus
      • March 15, 2025 at 6:07 PM
      • cus
      • April 4, 2025 at 8:48 AM
    3. Replies
      25
      Views
      1.1k
      25

    4. cus

      April 4, 2025 at 8:48 AM

    2. Rundheit von Felgen - Problem mit Genauigkeit 14

      • pfuetze
      • January 24, 2025 at 3:51 PM
      • pfuetze
      • February 13, 2025 at 8:41 AM
    3. Replies
      14
      Views
      735
      14

    4. pfuetze

      February 13, 2025 at 8:41 AM

    2. welches Resin wofür? 4

      • pfuetze
      • November 3, 2023 at 4:50 PM
      • pfuetze
      • September 10, 2024 at 4:42 PM
    3. Replies
      4
      Views
      936
      4

    4. MiniSlot

      September 10, 2024 at 4:42 PM

    2. OrcaSlicer 9

      • MiniSlot
      • December 8, 2023 at 10:10 PM
    3. Replies
      9
      Views
      3.4k
      9

    4. xervas

      December 8, 2023 at 10:10 PM

    2. Mein erster Druck mit dem Orca 10

      • xervas
      • November 22, 2023 at 5:48 PM
      • xervas
      • November 29, 2023 at 1:19 PM
    3. Replies
      10
      Views
      1.2k
      10

    4. xervas

      November 29, 2023 at 1:19 PM

    2. Ich brauche mal euer Wissen 2

      • xervas
      • August 15, 2023 at 6:23 PM
      • xervas
      • August 16, 2023 at 9:58 AM
    3. Replies
      2
      Views
      571
      2

    4. xervas

      August 16, 2023 at 9:58 AM

    2. welches Filament 1.75 6

      • xervas
      • August 1, 2023 at 4:00 PM
      • xervas
      • August 3, 2023 at 1:08 PM
    3. Replies
      6
      Views
      846
      6

    4. xervas

      August 3, 2023 at 1:08 PM

    2. Probleme mit Stringing und Blobs - Ender 3v2 17

      • Chaos_Bob
      • February 20, 2023 at 8:46 PM
    3. Replies
      17
      Views
      1.8k
      17

    4. Chaos_Bob

      February 20, 2023 at 8:46 PM

    2. Printables.com -> kostenloses Filament 2

      • Macbambi
      • February 12, 2023 at 5:29 PM
      • Macbambi
      • February 13, 2023 at 10:40 PM
    3. Replies
      2
      Views
      669
      2

    4. Macbambi

      February 13, 2023 at 10:40 PM

    2. PLA+ für wirklich kleines Geld 13

      • Macbambi
      • April 22, 2022 at 11:48 AM
    3. Replies
      13
      Views
      3.4k
      13

    4. Macbambi

      April 22, 2022 at 11:48 AM

    2. Welche Slicer nutzt ihr für SLA-Drucker und warum?

      • MiniSlot
      • January 2, 2022 at 7:45 PM
    3. Replies
      0
      Views
      883

    2. Probleme mit der Druckhaftung 25

      • OstBerlina
      • August 11, 2021 at 5:57 AM
    3. Replies
      25
      Views
      5.6k
      25

    4. Macbambi

      August 11, 2021 at 5:57 AM

    2. 3D - Drucker 42

      • OstBerlina
      • April 19, 2021 at 12:42 PM
    3. Replies
      42
      Views
      11k
      42

    4. MiniSlot

      April 19, 2021 at 12:42 PM

    2. Filament trocknen, bzw. trocken halten 5

      • Macbambi
      • April 10, 2021 at 7:47 PM
    3. Replies
      5
      Views
      2k
      5

    4. Macbambi

      April 10, 2021 at 7:47 PM

    2. Tipp - Druckqualität bereits in der CAD-Software verbessern 2

      • MiniSlot
      • April 1, 2021 at 11:16 PM
    3. Replies
      2
      Views
      1.8k
      2

    4. MiniSlot

      April 1, 2021 at 11:16 PM

    2. Überlegungen zum 3D-Druckbereich des Forum 31

      • Holgi2018
      • March 30, 2021 at 4:25 PM
    3. Replies
      31
      Views
      6k
      31

    4. xervas

      March 30, 2021 at 4:25 PM

    2. 3D Drucker - Tipp für eine CAD Software (Einsteiger) ? 5

      • Topsurfer
      • September 17, 2020 at 10:42 PM
    3. Replies
      5
      Views
      1.8k
      5

    4. ElCheffe

      September 17, 2020 at 10:42 PM

    2. 3D- Drucker Anet A8 - diverse Fragen .... 44

      • pfuetze
      • March 10, 2019 at 7:50 PM
      • pfuetze
      • March 27, 2019 at 11:19 AM
    3. Replies
      44
      Views
      12k
      44

    4. Johannes_AT

      March 27, 2019 at 11:19 AM

    2. Wie muss ein (Hohl)körper konstruiert werden für den 3-Druck über shapeways 8

      • Digisteve
      • September 21, 2018 at 8:22 PM
    3. Replies
      8
      Views
      2.9k
      8

    4. Ritze 143

      September 21, 2018 at 8:22 PM

    2. 3D-Drucker 7

      • CarGo
      • July 5, 2017 at 10:41 AM
      • CarGo
      • July 5, 2017 at 1:47 PM
    3. Replies
      7
      Views
      2.5k
      7

    4. CarGo

      July 5, 2017 at 1:47 PM

Display Options